However, it should be noted that cutting the alumina is a delicate process Alumina is a strong material due to it being made from this light white colored substance known as aluminum oxide. From traces of alumina in ceramics to the uses for it in circuit boards—this mineral is easy to spot in any crowd. At Datong, we understand better than anyone how essential it is to cut alumina the right way. Precision = Set Forward (This must be meticulous, these parts are between 1.5mm to right is best case of about 2mm too much or less can make the difference between it fitting well when you assemble end product and not being able to do so.)
In order to cut the alumina, factors include the specific devices and machines that help keep it cutting. With access to cutting edge tech and equipment at Datong, we cut every single piece perfectly. This in turn makes possible the much quicker and cheaper creation of even better alumina parts. We build machines designed to cut materials like Datong high alumina cement that allows us to pass through without a hiccup. These excellent tools are then combined (as in this demo) to save considerable time and resources while providing the software at a high level of quality.
If we choose to produce parts in alumina, Datong brown fused alumina must be engineered and manufactured with very high tolerances. Which can ultimately lead to issues in production, if the parts were wrong to begin with. In other words, if one part is a little bigger or smaller, it does not fit into any of the other parts and can cause your product to fail. For Datong, after many small and standard cutting ways to make every parts in an effective size. We literally watch every single cut and turn of the ruler to make sure it is perfect. Making them the way our customer wants – we are learning how to take measures over and over again!
We also use the world's top cutting tools and technologies, to absolutely perfect cut alumina parts at Datong. The smart software we have developed enables us to go to 3D models of the parts long before we start cutting. This way, we know where the end result will be cut and what our cutting lines have to match as much (and perfectly) as we can. We check the parts with special measuring tools after each cut to make sure they are ok to continue. Though the process up to this point is subject to a great deal of scrutiny, we are also able to catch any mistakes before parts are ever shipped out to our customer.
The Right Tools: Use non-scrap cutters (eg., predesigned cutting tools for alumina). If the tools are not proper, then you will have jagged edges and material waste.
Clean is Classy: A clean desk says to an employer. Our cutting area will be clean, however we can get the dust or dirt between components therefore final can be bad.
Pick your Experts: It never hurts to have a team of alumina cutting veterans in your corner like Datong. Datong calcined alumina subsequently makes the system move along in a good smooth flow and then the people undergoing will benefit greatly from the lessons and pointers of other who have been around for awhile.
Datong invested 10 million dollars and constructed a chemical analysis lab and a micro-powder testing room, Cutting alumina, application laboratory high temperature laboratory pilot base, and over 40 sets of various testing equipments, including SEM energy thermometer XRD laser particle size analyzer, and other top testing and analysis equipment. The technical center employs over 10 technical employees with 1 senior engineer and 2 engineers. It maintains a closely working relationships with Wuhan University of Science and Technology Sinosteel Luoyang Institute of research in refractories, University of Science and Technology Liaoning, Zhengzhou University and other research institutes within the area of Refractory.
Kaifeng Datong Refractories Cutting alumina was founded in 2008 and is a private joint-stock corporation located in Henan province. It specializes in the production and development of high-quality refractory material.
Datong has been awarded ls0900l quality system certification, is014001 environmental management system certification, OHSAS1800 occupational health and safety management system certification. is a national high-tech enterprise which was able to be listed on April 7th, 2016 with stock code Cutting alumina. Datong is now the largest and most complete collection of high-quality aluminum-based refractory materials. Every tank is inspected with hydraulic test, radiography test, and air tight test, etc. With world's advanced production machine and strict quality control at each production stage. We pay attention to each and every aspect, and each small action is an integral part of the workforce we employ.
We offer top-quality raw materials, high-quality products, and services, and we are growing with our customers. While at the same time. in order to provide Cutting alumina to customers, provide customers with other related quality products, Datong Company is willing to create and win-win cooperation with all its partners!
Copyright © Kaifeng Datong Refractories Co.,Ltd All Rights Reserved. - Privacy Policy- Blog
EN
AR
HR
CS
DA
NL
FR
DE
EL
HI
IT
JA
KO
NO
PL
PT
RU
ES
SV
TL
ID
LT
SR
SK
UK
VI
HU
TH
TR
MS
GA
CY
AZ
LO
LA
MN
NE
MY
KK
UZ
